如何管控：一定要先做确认（报工）再做入库

wanilycrf

这个地方好似只能配置不大于工单的数量，但是不能设置不大于报工的数量.
比如：创建的工单数量是100，最后一道工序只报工了80件，那么期望GR的时候缺省的数量是80而不是100.

原帖由 LostHorizon 于 2011-1-12 16:19 发表



In related order type（OPK4）， you try to need to set overdelivery to error when it exceed...

seantu

原帖由 bennyzeng 于 2011-1-11 21:41 发表
Pls follow this:

1. Use Tcode BS02 ( Customizing Users status profile).

2. Select the order type which you want to configure (eg:PP000001) and choose "Details" button.

3. In the User status table do the following:

a. In the status no field type"1" , status field "Sta1", short text"GR not allowed",  lowest no "1",  Highest No "2". Mark a tick in the initial stats check box.
b.Next line, type status no field "2" ,status field "sta2", short text"Gr allowed", lowest no "2" , highest no "2".

4. Select the STA1 line and choose details. select the "create"button.select the "GR for prod order", mark "forbidden radio button" and "set radio button".

5. Select the STA2 line and choose details. Selct the "create"button. select "confirm order", mark "permitted radio button" and "set radio button". Next choose "GR for prod order" , mark "permitted radio button".

6 select the SAT1 line and choose details. select the "create" button & select "GR for production order", mark"Forbidden" ratio button and "Not active" button.

7*select the "SAT2" line and choose details. select the "create" button & select "confirm order", mark"allow" ratio button and "set" ratio button. Next "GR for production Order", mark "Allowed" ratio button and "set" ratio button.*

8 Save

9 Now assign your Status profile"XXXXX" in th production order type (OPJH) -----Status profile header:-XXXXX

This will not allow you to do GR for production order when you activate status profile "SAT1" in the production order. After that when you confirm order it will automatically assign next user status i.e. "SAT2" (*if not assign it manually in CO02*) it will allow you to do GR for that production order.
If you still face any problem reply back.
Q:I\whether At SAT1  this can control 1.disable DLV before CNF & 2.be able to PCNF/PDLV  & 3.activate SAT2 when CNF  ?
II\ whether this can only be able to DLV AT SAT2
10 Create a prod order and check whether the required scenario is working.

[ 本帖最后由 seantu 于 2011-1-12 17:26 编辑 ]

LostHorizon

原帖由 wanilycrf 于 2011-1-12 17:18 发表
这个地方好似只能配置不大于工单的数量，但是不能设置不大于报工的数量.
比如：创建的工单数量是100，最后一道工序只报工了80件，那么期望GR的时候缺省的数量是80而不是100.

hum... have you tested both together including recommended from bennyzeng?

wanilycrf

thanks.
I will let my friend test it,because I have quit from the previous company, and now I donot configue PP module.

staryoung

顶六楼

xyhstrive

这个只能设置不超过订单的数量入库。

回不去的家乡

学习了。